POWER CONTROL 110-240V 4000VA for motors, heaters and bulbs
search
  • POWER CONTROL 110-240V 4000VA for motors, heaters and bulbs
  • POWER CONTROL 110-240V 4000VA for motors, heaters and bulbs
  • POWER CONTROL 110-240V 4000VA for motors, heaters and bulbs
  • POWER CONTROL 110-240V 4000VA for motors, heaters and bulbs

POWER CONTROL 110-240V 4000VA for motors, heaters and bulbs

€40.00
Tax included

This device allows you to control the power supplied to light bulbs (filament or halogen), motor speed (drills, fans ... etc), electric heaters by means of a knob potentiometer provided.

Quantity
Last items in stock

  Secure payments

You can pay safely by Card, PayPal, Amazon Pay or Bank Transfer

  Delivery policy

Express shipments with DHL, BRT, GLS

  Return policy

You have 15 days from delivery to return the product if you are not satisfied

MANUAL | INSTALLATION WARNINGS

This device allows you to control the power supplied to light bulbs (filament or halogen), motor speed (drills, fans ... etc), electric heaters by means of a knob potentiometer provided.

The maximum load is 4000VA continuous on 230V AC with the device installed on the heatsink not supplied. The device is ideal for resistive and inductive loads.

The knob potentiometer allows direct control by knob of the power from 0% to 100%.

Universal power supply from 110V AC to 240V AC.

The device, excluding the potentiometer, is installed in a plastic container with an aluminum rear part that can be installed on a heat sink or metal casing.

For those who wish, it is possible to integrate the device with external devices capable of allowing power control via analog voltages or PWM modulations from external electronic circuits instead of the manual potentiometer supplied. For more information you can contact us.

You can use this device with some optional accessories to be able to control the power of 230V loads such as lamps and motors directly from electronic systems or even through embedded systems or PCs through a home automation system on RS485 BUS. Link for purchase and information EBAY | MECTRONICA STORE

SPECIFICATIONS:

  • Input voltage: 110-240V AC at 50 / 60Hz (universal power supply)

  • Maximum allowed current and load: 18A (if installed on a suitable heatsink not supplied) corresponding to 2000VA at 110V AC and 4000VA at 230V AC

  • Without heatsink, maximum current 6A corresponding to 1380VA at 230V (25A for a maximum of 10 seconds)

  • Power control by means of a rotary knob potentiometer installed on a wire connected to the device via faston. Possibility of external electronic controls (read description)

  • For resistive ohmic and inductive loads

  • Connection: 2 faston for potentiometer connection (supplied), 2 faston connection in series with load for power control

  • Power regulation by phase control

  • Dimensions approx. 87 x 60 x 33 mm



INSTALLATION WARNINGS

Depending on the load the module heats up. Heat is dissipated by the aluminum plate at the bottom of the module. Under certain circumstances it must be mounted on a cooling surface according to the installation instructions. It is important that the module is fixed with 4 M3 screws (or 2.9mm metal screws) on the cooling surface. This can be the back wall of a metal enclosure. The aluminum plate on the bottom of the module must not bend, do not use larger screws, and do not drill larger holes. The screw heads must rest on the module plate, instead of the plastic edge of the module! During assembly, the module must not be curled up (if the ground is not flat). The reason: inside the aluminum base of the module the thin insulation layer is directly soldered on the SMD electronic components. Make sure that the maximum expected temperature (as specified in the module description) is not exceeded. If not, apply a larger cooling plate.

M028N
4024028032924
1 Item

You might also like